![]() To replace, fit into place and twist to the right.Īfter emptied, place tank back on vacuum and press firmly until you hear “click”. Let cyclone completely dry before replacing. Twist cyclone left and pull down to remove from tank.Ĭlean cyclone with warm water and mild detergent. Press the bottom release button to empty. Hold the Dirt Tank over a trash container. Press the tank release button and pull out to remove Dirt Tank. WARNING To reduce the risk of electric shock, turn power switch OFF and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks. Static discharges are entirely harmless and are not associated in any way with the main power supply. NOTE: Certain carpets and low humidity conditions may generate small static discharges. Do not place vacuum close enough to objects to pull into rotating brush. Never place PowerFoot on furniture or uneven surfaces. Never place fingers under the vacuum when it is running. NOTE: Rotating floor brush continues to rotate while tools are in use. If the cord doesn’t fully retract on the first try, pull a little bit of cord out and press the rewind button again. Hold onto the plug and press the automatic cord rewind button until it’s fully retracted. When you finish using your vacuum, unplug it from the outlet. Once you have the desired amount of cord, plug it into the outlet. To plug your vacuum in, gently pull the cord out of the automatic cord rewind and stop at the yellow mark on the cord. If your vacuum is difficult to push, adjust to the next higher setting. TIP: For optimal carpet cleaning performance, adjust to the lowest practical setting. Highest setting – For high pile and most shag carpet. To pick up debris, it may be necessary to move up one setting. Lowest setting – For low pile carpet or bare floors. If the dial is difficult to turn, tilt the vacuum back slightly to take the weight off the foot while turning. Turn the dial on the foot of the vacuum to the desired setting. ![]() Press the recline pedal and pull handle back towards you. Press the red power button with your foot to turn the vacuum ON and once again to turn your vacuum OFF. Always place vacuum on floor with handle in upright position when using tools. Do not carry the vacuum while it is running. WARNING To reduce the risk of injury from moving parts while the vacuum is turned ON, always move the vacuum via the rolling wheels by using the upper handle at the back of the vacuum. NOTE: The Powerfoot will not suction properly unless the hose is firmly attached. Now, put your accessory tools on the vacuum and you’re ready to go! Wrap hose up and around the hose wrap on the handle. Insert the hose end into the back of the vacuum and twist right to lock in place. Insert the Extension Wand base and turn it to the right to lock in place. ![]() Then attach the handle with the 2 screws taped to the handle in a plastic bag. Place the upper handle onto the base and push it down. The only tool you will need to assemble your vacuum is a Phillips-head screwdriver. NOTE: The Crevice Tool is stored inside the Extension Wand. WARNING Do not plug in your vacuum until you are familiar with all instructions and operating procedures. Removing the hair without opening the brush housing requires a razor blade or scissors.Bissell 2490 Cleanview Rewind Pet Vacuum Cleaner - Use Manual - Use Guide PDF. Use your fingers, a pipe cleaner, or a skewer to clean out stuck debris. If your vacuum suddenly loses suction, disconnect the hose, wand, and cleaner head and look for clogs in each part. Over time, hair and other fibers will wrap around the vacuum’s brush roll use scissors or a blade to cut those off and keep the brush rolling freely. And if you’re washing a reusable filter, let it dry thoroughly before putting it back in the vacuum. Check the manual to see which filters to clean or replace and how often (the advice varies widely by manufacturer). When a vacuum’s filters get clogged with dust, it loses suction. On the same note: Don’t wait to replace the bag of your Miele or SEBO until it’s completely stuffed. A bagless vacuum requires you to empty the canister after a run or two. This is important: A stuffed bin prevents airflow, and airflow is essential for your machine’s cleaning power. Empty the bin or replace the bag regularly.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |